Uncategorized Archives - Page 3 of 9

2017 Jeep Wrangler
Mileage
61,154
Service Date
3/12/2020
Services Performed
Perform brake inspection
REPLACE FRONT PADS – Remove & Replace – Front,Both Sides – [Includes: Clean, lube and/or replace Brake Hardware as necessary. Adjust Brakes (where applicable). Includes: Repack Wheel Bearings (where applicable). DOES NOT include refinishing.]
Replace missing brake hardware springs
RICHIE L. gave our service a 5 star review on 3/13/2020
2017 Nissan Altima
Mileage
54,972
Service Date
11/1/2019
Services Performed
CABIN AIR FILTER – Remove & Replace – All Applicable Models
Perform oil and filter
ERICA T. gave our service a 5 star review on 11/2/2019
2017 Nissan Altima
Mileage
52,343
Service Date
8/9/2019
Services Performed
Road tested vehicle, no brake squeal heard when driving. Raised vehicle on lift and removed wheels to inspect brakes, rear brake linings currently less than 1mm and rear brake rotors at discard limit, recommend replacing. Front brake pads at approx 4mm lining remaining, replacement likely necessary in near future.
Replace rear brake pads and rotors
BATTERY – Remove and Replace – All Applicable Models – [Includes: Test.]
ERICA T. gave our service a 5 star review on 8/12/2019
2015 Toyota Tundra
Mileage
42,767
Service Date
5/8/2019
Services Performed
SPRING – Remove and Replace – Front,Both Sides – Install new front struts and strut mounts also
STABILIZER BAR – Remove and Replace – w/Skid Plate
SHOCK and /OR STRUT ASSEMBLY – Remove and Install or Remove and Replace – Both – [Includes: Bleed Brake System (where applicable). DOES NOT include disassemble or alignment (where applicable).]
Install TRD rear stabilizer bar assembly
SHIPPING AND HANDLING CHARGES FOR PARTS
TWO WHEEL ALIGNMENT – Adjustment – Front Axle – ALIGNMENT PREPAID
Brent G. gave our service a 5 star review on 5/9/2019
2016 Chevrolet Silverado 1500
Mileage
36,664
Service Date
10/29/2018
Services Performed
CONTROL ARM – Remove and Replace – Upper,Both – [DOES NOT include alignment.]
SHOCK and /OR STRUT ASSEMBLY – Remove and Install or Remove and Replace – Both – [DOES NOT include disassemble or alignment (where applicable).]
TWO WHEEL ALIGNMENT – Adjustment – Front Axle – [Includes: Steering Angle Sensor Centering procedure.] – [DOES NOT include straightening or replacement of components.]
SHOCK ABSORBER – Remove and Replace – Both
ANDREW S. gave our service a 5 star review on 10/31/2018
2006 Chevrolet Silverado
Mileage
127,995
Service Date
10/26/2018
Services Performed
Replace tailgate latch clips
LEONARD A. gave our service a 5 star review on 10/30/2018
2006 Jeep Grand Cherokee
Mileage
103,678
Service Date
8/24/2018
Services Performed
Wear noted , suggest to monitor for now
CANDACE T. gave our service a 5 star review on 8/25/2018
2005 Dodge Pickup
Mileage
68,144
Service Date
8/14/2018
Services Performed
Belt missing. water pump pulley loose, also no coolant in cooling system. Drove vehicle in parking lot to verify that there are no obvious engine miss/misfiring; ok. Belt idler pulley noisy, recommend to replace also. RECOMMEND TO REPLACE WATER PUMP, THERMOSTAT, IDLER PULLEY AND DRIVE BELT.
All brakes approximately 5-6mm; 50% remaining.
WATER PUMP – Remove and Replace – V8,4.7L Eng
THERMOSTAT and /OR GASKET – Remove and Replace – V8,4.7L Eng
ENGINE DRIVE BELT AND SMOOTH IDLER PULLEY – Remove and Replace – Gas; no additional labor.
DONNA H. gave our service a 5 star review on 8/17/2018
2005 Honda S2000
Mileage
63,769
Service Date
7/3/2018
Services Performed
Clutch hydraulic fluid is black in color and appears very thick, no clutch hydraulic components appear to be leaking currently. Recommend flushing out system, replenish with new fluid and vent system of potential air, Perform fluid flush twice to remove residual fluid , system now performs as per design and intent .
Flush and renew brake fluid .
Flush hydraulic fluid for clutch and bleed system of air , performed twice to remove residual fluid
TED K. gave our service a 5 star review on 7/4/2018
2006 Chrysler Crossfire
Mileage
50,824
Service Date
5/18/2018
Services Performed
Vehicle will not crank, also remote central locking inoperative, no locking or unlocking. Check vehicle four trouble codes; P2071-8 (start enable not sent to engine module; Drive authorization). Perform electrical test for drive authorization; CAN C, power supply and ground signal ok to Security Key Remote Electronic Entry Module; Perform hard reset disconnect to module and found that vehicle will now start up; module has intermittent electronic malfunction. Note* If problem persists, then it is recommended to replace theSecurity Key Remote Electronic Entry Module and program. Cleared all trouble codes. Vehicle starting operation normal after reset of Security Key Remote Electronic Entry Module and central locking now working also.
1) Left side valve cover leaking; recommend to reseal both side valve cover gaskets. 2) Ask client about vehicle service history; transmission service, brake flush, coolant flush, spark plugs, etc.
JIMMY K. gave our service a 5 star review on 5/23/2018

Uncategorized

We Service and Repair all Uncategorized cars