Check vehicle for trouble codes; Engine = 0064 (Continuous cam adjustment left; Incorrect position of exhaust cam), 0629,0641,0637 (Misfiring, cyls 3 and 4). Removed spark plugs for cylinders 3 and 4 for inspection; found spark plug for cylinder #4 has 0.015 inch gap; re-gap spark plug and swap spark plugs between cylinders 4 and 6 and cylinders 1 and 3. Also swapped ignition coils between cylinders 2 and 3 and cylinders 4 and 5. Clear all trouble codes and road test; no misfiring redetected by engine module; client to monitor. As for the camshaft code #0064, Recommend to replace Lt/side exhaust cam solenoid magnet.
Inspect brake system; Could not verify soft brake pedal. Front and rear brake pads at approx 50% pad material remaining. Brake fluid dirty, Recommend brake fluid flush.
Found Lt/side mirror turn signal LED lense has internal electrical malfunction.Recommend to replace Lt/side mirror turn signal lense
1) Service B Maintenance reminder coming on dash; Recommend Service B Maintenance. 2) Rt/frt marker bulb out warning coming on. Recommend to replace Rt/frt marker lense and bulb. 3) Belt drive noisy at front of engine while running, sound like tensioner knocking, Also light squeaking noise; Diag required. 4) Rt/frt position lamp bulb cover missing on Rt/side headlamp unit. needs to order cover, if available. 5) Brake fluid dirty; recommend flush. 6) Engine air filter dirty; recommend replace. 7) Engine air filter dirty; recommend replacement. 8) Hood shocks weak/worn; recommend replacement. 9) Coolant flush due every 100k miles; recommend flush. 10) Transmission service due at 40k and 100k; recommend transmission service. 11) Vehicle has incorrect size systems battery, battery hold down does not secure battery. Recommend replacement.
CYNTHIA S. gave our service a 5 star review on 9/17/2018
Provide estimate to remove cylinder heads and send out for inspection and refinish. When engine is started coolant oil leaks from passenger side cyl. head
Removed cylinder heads and found cylinder bores 1,4 and 8 have pitting/wear and discoloration on cylinder walls. Corrosion on cylinder walls look to be from standing water/moisture that has been sitting in engine cylinders for several months during storage, rather than from coolant leaking into cylinders from when vehicle/engine was operational. Cylinder walls cannot be repaired due to factory coating on surface of cylinder bores, Also pitting on bores cannot be repaired. RECOMMEND TO REPLACE ENGINE LONG BLOCK, BUT CLIENT DECLINED ENGINE REPLACEMENT AND INSTRUCTED TO PROCEED WITH REPAIRS ONLY TO THE CYLINDER HEAD GASKET REPLACEMENT AND CYLINDER HEAD RECONDITIONING AT THE MACHINE SHOP. NOTE* THERE ARE NO WARRANTIES ON REPAIRS RELATING TO PRE-EXISTING CONDITION WITH ENGINE BLOCK/CYLINDER WALLS AND WITH PROBLEMS ARISING FROM CONDITION WITH CYLINDER WALLS. THE WARRANTIES THAT ARE ON THE REPAIRS ARE FOR 12 MONTHS OR 12,000 MILES, WHICHEVER COMES FIRST, AND ARE FOR THE PARTS INSTALLED AND THE WORKMANSHIP OF THE REPAIRS FOR THE CYLINDER HEAD GASKET REPLACEMENT, UNLESS THE PARTS AND/OR WORKMANSHIP HAVE BEEN COMPROMISED BY THE PRE-EXISTING CONDITION OF THE ENGINE CYLINDER WALLS.
Perform B service , change oil and filter , perform battery charging system test , rotate tires if applicable , perform brake inspection , replace a-c cabin filter , perform balance of flex inspection , reset maint. light
Checked for fault codes with scan tool, found ESP warning comes on due to faulty stop lamp switch, recommend replacing. At this time there is currently no fault codes in transmission control module. Road tested vehicle, shudder can be felt when driving normally in lower gears. Checked transmission adaptations, all appear okay and within specifications. Found at times when putting vehicle in reverse, there is a delayed reaction before vehicle will start to move. Service bulletin LI27.00-P-047119 found for delayed reverse engagement, transmission software must be updated and a relearn procedure of the range selector must be performed. Also checked fluid level and condition of fluid, level is currently okay but fluid is dark in color. At this time, must start with recommending performing software update of transmission, service transmission and then perform shift adaptations and see if shudder still persists.
DENISE L. gave our service a 5 star review on 7/17/2018
front brake pads needed, rotors optional: front pads worn down to wear sensors, 1mm left, rotors are in spec at 30.5mm minimum is 29.6mm, there is a lipped edge worn into the rotors, which will cause brake noise to occur on the new pads
Remove cd player , disassemble unit , remove coins . Unit works as per design
Replace front brakes and rotors, sensor
MATTTHEW K. gave our service a 5 star review on 6/20/2018
Client states was told , guide arm bushings were torn , motor-transmission mounts were worn , spark plugs due by mileage , C service due soon . Please inspect vehicle to confirm this concerns
3) Hood shocks worn, no support. Recommend replace. 4) Both front wheels bent. Recommend replace/repair. 5) Brake fluid dark/dirty. Recommend flush. 6) Engine air filter dirty/dusty. Recommend replace. 7) Recommend spark plug replacement. due by mileage. 8) A/C dust filter dirty, recommend replace. 9) Transmission service due by mileage; see client's service history first.
THRUST ARM BUSHING – Remove and Replace – Base,RWD One Side
Four wheel alignment , bolt kit will be needed to correct very slight pull . Estimate 260.00
ENGINE OR TRANSMISSION MOUNT – Remove and Replace – RWD All
Perform oil and filter . RESET MAINT. LIGHT
CANDACE T. gave our service a 5 star review on 4/26/2018